STAR TRAC FITNESSTMPERSONAL VIEWING SCREENO WNER’ S M ANUAL
The Star Trac Personal Viewing Screen is different for each of your Star Trac E-Series Cardio prod-ucts. Make sure you have the proper kit for the E-
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE11After all the cable/harnessing has been disconnected, place the front display plastics aside for lateruse
STEP 7Install the (4) M8 Buttonhead Screws through thePVS mounting bracket into the display mount.Note: (2) of the screws are in the PVS kit, (2)retai
STEP 10Using a #2 Phillips head screwdriver, remove thescrew that holds in the blank cover where the newHead Phone Jack mount will go. Next remove th
With the changes now completed on the display, it is now time to re-install the display to the base unit.There are the (3) cables from the PVS mount t
STEP 16Using a tie wrap from the PVS kit, bind the cablesfrom the PVS neck to one side of the displaymount. Take the tie and put it through the hole
STEP 19Feed the Head Phone Jack cable from the PVSdisplay neck through the hole in the front displayplastics where the blank cover was removed earli-e
STEP 23Now with the Personal Viewing Screen installed onyour Star Trac equipment, it is time to connect yourentertainment cable and power to the unit
To install on the E-TR, follow these steps:STEP 1Using a #2 Phillips screwdriver, removethe (8) screws from the upper back ofthe display. Place the c
STEP 4Detach the Center Console Ribbon Cable from thedisplay board by gently pulling on the ribbon con-nector. Using a #2 Phillips screwdriver to rem
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEP 8Now that the PVS is mounted to the Treadmill, youneed to route the wires to their proper places.Take the coax cable and feed it all the waydown
STEP 10While holding the New Center Console near the opening of the display, connect the following cablesto there approprate connector.(There is no pa
STEP 13From below the display, connect the CenterConsole Ground Cable to the QuickDisconnect Tab on the display mount.Connect the Keypad Tail to the
STEP 17Replace the top back plastic. Using a #2 Phillipsscrewdriver insert the (8) screws, retained fromearlier step, into the plastic. Do Not tight
24 STAR TRAC PERSONALVIEWINGSCREENOWNER’SMANUALNow that your Personal Viewing Screen is installed on your Star Trac Cardio Equipment, it is time toset
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE25To navigate through the setup screens you will use the Entertainment Center Console keypad. Tomove betwe
26 STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDETUNING BANDAir: Use this selection when a terrestrial(indoor/outdoor) antenna is used.Cable: Use this se
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE27CHANNEL LABELSYou can change the channel labels for each of the viewable channels. Analog channels are s
28 STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDEBRIGHTNESS: Adjust to brighten or darken the picture.SHARPNESS: Further you go left, more the screen sof
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE29TREBLE: Will adjust the treble tone for the sound output.BALANCE: Will adjust the sound volume between th
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE3iPULSETMiPULSETME-UBi, E-RBi, E-STi, AND E-TBTiE-TRi
PAL / SECAM Personal Viewing Screen Set upBefore you can set up the Personal Viewing Screen you must first get into the “Maintenance Mode” ofthe Star
7. Press the to exit.This completes the E-TR setup, now turn to the “Accessing The On Screen Display” to continue.For “Maintenance Mode” on the E-TBT
ACCESSING THE ON SCREEN DISPLAY (OSD)To enter the On Screen Display (OSD) setup menu, you need to press and hold the and, and at the same time press t
ADJUSTING THE ON SCREEN DISPLAYPICTURE MENUUse the to navigate to the Picture menu. To enter the sub menu press . Use theand to navigate to the de
SETTING THE SOUNDThis menu is for adjusting the following items.Sound Mode: Default is StandardBass: Will adjust the bass tone of the sound output.Tre
SETTING UP THE CHANNELSThis menu is for adjusting the following items.Country: Provide a list of country settings supported by PVS.Search Option: All,
SETTINGS MENUThis menu is for adjusting the following items.Clock: PVS clock time.On Time: On time.Off Time: Off Time.SleepTimer: Enable on off timers
STAR TRAC PERSONALVIEWINGSCREENOWNER’SMANUAL37Your Star Trac Personal Viewing Screen is designed with little maintenance in mind and rarely shouldyou
38 STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDEPoor Picture Check the input signal cable, make sure it is in good shape and is con-nected snug to the R
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE39Headphone Jack Replacement.When you are experiencing poor audio output from your PVS, you should check th
Thank you for adding the STAR TRAC PERSONAL VIEWING SCREEN (PVS) to your Star Trac Purchase. The PersonalViewing Screen has been designed to provide t
40 STAR TRAC PERSONALVIEWINGSCREENOWNER’SMANUALREGULATORYINFORMATIONRadio Frequency Interference (RFI)Federal Communications Commission, Part 15 Warni
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE41
Part Number 620-7838 REV A , July 2008STAR TRAC14410 Myford RoadIrvine, California 92606Telephone: (800) 228-6635, (714) 669-1660Fax: (714) 508-3303ht
CHECK FACILITIES PREPAREDNESSFor a proper installation, please read this guide thoroughly and follow the instructions. Star Trac’s goal is to help you
This lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the userto the presence of uninsulated “dangerous vol
This STAR TRAC Personal Viewing Screen has been engineered and manufactured to assure your safety. Before usingthis product, be sure to read your use
UNPACK YOUR PERSONAL VIEWING SCREENInspect the shipping carton for any parts that may be missing BEFORE discarding the carton. Items can shift during
STAR TRAC PERSONALVIEWINGSCREENOWNER’SGUIDE9• Power Cord, Nema 6-15 (NOT INCLUDED IN THE E-TRi KIT)• Power Cord, Nema 5-15 (NOT INCLUDED IN THE E-TRi
Commentaires sur ces manuels